Project Phil's 1975 Honda Civic 1200
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Project Phil's 1975 Honda Civic 1200
I'm going to continue on from my introduction thread here...
The car is still a work in progress, including some things that I intially didn't intend doing. My Mechanical friend has helped me through the majority of this process.
The removal of the EB1 engine, gearbox and all engine bay components. Originally planned to do a major service and replace all seals etc.
A decision was made to repaint the engine bay in yr-22 sunset orange ( and the rest of the car when finances allow). This was quite a challenge to get the correct
mix, I finally settled on the 3rd suppliers offering.
Getting the engine bay ready for painting has been a long process with no lack of sacrificial blood spared to the Civic Gods. I wasn't a huge fan of the Ford washer bottle, so it will be replaced with one of my original washer bags and motors.
Let the rust treatment begin!
I started with the removal of all seam sealer with a few picks (1 broke) and a scraper. The result revealed surface rust, which I managed to wire wheel and treat with rust converter. Rinsed and repeated this process for the whole engine bay.
Welded reinforcement of left engine mount, a little panel beating and body filler to get closer to the original shape.
Did I mention degreaser???
More to come soon, stay tuned!
The car is still a work in progress, including some things that I intially didn't intend doing. My Mechanical friend has helped me through the majority of this process.
The removal of the EB1 engine, gearbox and all engine bay components. Originally planned to do a major service and replace all seals etc.
A decision was made to repaint the engine bay in yr-22 sunset orange ( and the rest of the car when finances allow). This was quite a challenge to get the correct
mix, I finally settled on the 3rd suppliers offering.
Getting the engine bay ready for painting has been a long process with no lack of sacrificial blood spared to the Civic Gods. I wasn't a huge fan of the Ford washer bottle, so it will be replaced with one of my original washer bags and motors.
Let the rust treatment begin!
I started with the removal of all seam sealer with a few picks (1 broke) and a scraper. The result revealed surface rust, which I managed to wire wheel and treat with rust converter. Rinsed and repeated this process for the whole engine bay.
Welded reinforcement of left engine mount, a little panel beating and body filler to get closer to the original shape.
Did I mention degreaser???
More to come soon, stay tuned!
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Phil's 1975 Honda Civic 1200
I tossed up between two different engines, the EK1 (1751cc) and the EN1 (1335cc). The EK1 requires a heavier amount of fabrication work, cost and would make the car somewhat front heavy. The EN1 requires minimum fabrication work and is somewhat plug and play, as long as the stock exhaust manifold is used.
I decided on the 1335cc EN1 2nd generation civic engine. Something with a little more pep and ability to keep the classic look and feel.I managed to obtain one at a local wrecker for a price, though inclusion of ancillaries was a bonus. Not the prettiest thing I've seen, but I am assured she will run with some TLC (the engine even reads 'V good').
I'm going to cover the EN1 installation in this thread, especially requirements for mounting in detail.
Note: All data obtained has been from the forum and its members. I am very thankful for the advice, in particular Gusto for extensive data spreadsheets and ongoing wisdom.
I decided on the 1335cc EN1 2nd generation civic engine. Something with a little more pep and ability to keep the classic look and feel.I managed to obtain one at a local wrecker for a price, though inclusion of ancillaries was a bonus. Not the prettiest thing I've seen, but I am assured she will run with some TLC (the engine even reads 'V good').
I'm going to cover the EN1 installation in this thread, especially requirements for mounting in detail.
Note: All data obtained has been from the forum and its members. I am very thankful for the advice, in particular Gusto for extensive data spreadsheets and ongoing wisdom.
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Phil's 1975 Honda Civic 1200
A few small projects I've been working at on the side...
Radiator - 3 row recore from local radiator shop (original 1200 radiator came with 2 rows).
Thermo fan shroud - sanded back with 400 grit wet and dry and repainted satin black.
Fan blade - sanded the fan blade using 1000 grit wet and dry to restore a cleaner finish.
Fan motor cap - sanded back with 1500/2000 grit wet and dry, before proceeding to polish for a good hour or so with autosol.
Radiator - 3 row recore from local radiator shop (original 1200 radiator came with 2 rows).
Thermo fan shroud - sanded back with 400 grit wet and dry and repainted satin black.
Fan blade - sanded the fan blade using 1000 grit wet and dry to restore a cleaner finish.
Fan motor cap - sanded back with 1500/2000 grit wet and dry, before proceeding to polish for a good hour or so with autosol.
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Phil's 1975 Honda Civic 1200
Suspension - A necessary replacement for weeping struts. Impressive they aren't gushing out considering they're 44 years old.
Option B is the option, option BC racing coilovers. Engineered and developed by our own forum members through years of hard work and personal investment. Thank you!
Specific chosen model: A-50-RA, custom 4kg front/2kg rear - Clevis type rear mount (I have a 3 door non-CVCC 1200 hatch). I used the UK site as reference to get the correct code.
Note: custom 4kg front/2kg rear configuration suggested by Louis Been for mainly street application.
Installation pending...
My sheds were robbed/searched recently (first sign of entry was a storage container full of brake drums with the writing 'Abestos best left alone'. You would have to be keen to open that one. The BC racing C-spanners and all my tools were stolen, but it's a blessing my 1200 parts weren't taken. They now reside in my house!
Option B is the option, option BC racing coilovers. Engineered and developed by our own forum members through years of hard work and personal investment. Thank you!
Specific chosen model: A-50-RA, custom 4kg front/2kg rear - Clevis type rear mount (I have a 3 door non-CVCC 1200 hatch). I used the UK site as reference to get the correct code.
Note: custom 4kg front/2kg rear configuration suggested by Louis Been for mainly street application.
Installation pending...
My sheds were robbed/searched recently (first sign of entry was a storage container full of brake drums with the writing 'Abestos best left alone'. You would have to be keen to open that one. The BC racing C-spanners and all my tools were stolen, but it's a blessing my 1200 parts weren't taken. They now reside in my house!
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Phil's 1975 Honda Civic 1200
A continuation of sanding, more sanding and more sanding for a respectable level of paint preparation.
Primer is on!
Wheel arch sound deadening paint.
YR-22 Sunset orange the bay! (The front grille section will be satin black)
Pleased with how the painting has turned out so far. When the budget and time allows, the car will go through a full strip down, rust treatment and inside out orange makeover.
Note: Thank you Jay for confirming the YR-22 colour samples.
Primer is on!
Wheel arch sound deadening paint.
YR-22 Sunset orange the bay! (The front grille section will be satin black)
Pleased with how the painting has turned out so far. When the budget and time allows, the car will go through a full strip down, rust treatment and inside out orange makeover.
Note: Thank you Jay for confirming the YR-22 colour samples.
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Phil's 1975 Honda Civic 1200
The engine has arrived!
It looks like the En1 has been rebuilt previously, based on the modern sealant used. Quite happy with the finish on the head. Will try to replicate this same look for the block.
So far, I've removed the heatshield, exhaust manifold and cleaned up the exhaust ports.
The engine was missing the water bypass pipe. I will be modifying an EB version to suit by moving the bracket location.
It looks like the En1 has been rebuilt previously, based on the modern sealant used. Quite happy with the finish on the head. Will try to replicate this same look for the block.
So far, I've removed the heatshield, exhaust manifold and cleaned up the exhaust ports.
The engine was missing the water bypass pipe. I will be modifying an EB version to suit by moving the bracket location.
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Phil's 1975 Honda Civic 1200
Last edited by Phil on September 2nd, 2019, 7:07 am, edited 2 times in total.
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Phil's 1975 Honda Civic 1200
I lightly sanded back and resprayed the grille in black a couple months ago, attempting to keep some of the original texture.
Very recently I attempted to mask off and spray the silver borders. Word of warning - not all painters tape is the same... I ended up for little metallic flecks of overspray that penetrated through the tape. I was however rather pleased with my scalpel work, albeit time consuming.
Thermo fan it its complete form
I pulled off the water pump + harmonic balancer pulleys for quick de-rust clean up.
Shortly after this I was off to the auto store for engine enamel primer and cast iron vht. Pleased with the finish.
My 7kg EB1 flywheel is currently at Enfield clutch awaiting a shave and balance. Aiming for 5-5.5kg final weight to make the car slightly more rev happy.
This evening I was fortunate enough to acquire a genuine RS exhaust manifold from long time member Gusto. I look forward to getting these ceramic coated in the next few weeks.
I am looking for information on secondaries to suit. I will likely get these custom made. Any recommendations on length Vs power band?
Cheers,
Phil
Very recently I attempted to mask off and spray the silver borders. Word of warning - not all painters tape is the same... I ended up for little metallic flecks of overspray that penetrated through the tape. I was however rather pleased with my scalpel work, albeit time consuming.
Thermo fan it its complete form
I pulled off the water pump + harmonic balancer pulleys for quick de-rust clean up.
Shortly after this I was off to the auto store for engine enamel primer and cast iron vht. Pleased with the finish.
My 7kg EB1 flywheel is currently at Enfield clutch awaiting a shave and balance. Aiming for 5-5.5kg final weight to make the car slightly more rev happy.
This evening I was fortunate enough to acquire a genuine RS exhaust manifold from long time member Gusto. I look forward to getting these ceramic coated in the next few weeks.
I am looking for information on secondaries to suit. I will likely get these custom made. Any recommendations on length Vs power band?
Cheers,
Phil
-
- Member
- Posts: 20
- Joined: April 23rd, 2007, 11:13 am
- Province/State: Central Valley, California
Phil's 1975 Honda Civic 1200
Phil, thanks for keeping us up to date. Appreciate the extra time and effort it takes to document what you are doing. I also have a 75 1200, and am hoping to put a 1335 in there, however with little time to work on it right now. Will be following your progress! - Joe
-
- Projects
- Posts: 65
- Joined: November 30th, 2018, 3:58 am
- Province/State: SA
- Model: 1975 Hatchback
Re: Phil's 1975 Honda Civic 1200
No worries Joe, hopefully some of the information assists with your build!joe wrote: ↑September 2nd, 2019, 12:43 pmPhil, thanks for keeping us up to date. Appreciate the extra time and effort it takes to document what you are doing. I also have a 75 1200, and am hoping to put a 1335 in there, however with little time to work on it right now. Will be following your progress! - Joe